Quantum Unlock Change Logs

11/19/24 - v0.1.45 Beta:

• Added Live mode to view patterns in real time
• Added ability to configure selected bar types and unlock levels without an attached bar
• Fixed single color options with spoiler and pillar mounts
• Fixed split arrow arrow patterns

09/11/24 - v0.1.44 Beta:

• Added notification for users to close other Feniex apps if open. (Mac uses will receive a popup to allow screen capture)
• Added Wire Harness designation for all bars
• Fixed numbering of configuration steps to be sequential
• Revised single (TD, STT, WK and Alley) options for all bars
• Fixed improper module assignment with Rear FLBs and Light Sticks after config downloads
• Fixed 60 day lockout for Quad 1.0 bars

07/03/24 - v0.1.43 Beta:

• Added ability to configure quantum bars without bar plugged in
• To trigger upate you can restart the app and wait 2 minutes for download

05/28/24 - v0.1.41 Beta:

• Added 60 day color lockout to Quad unlock levels
• Fixed long wait for app install and update
• To trigger upate you can restart the app and wait 2 minutes for download

05/10/24 - v0.1.40 Beta:

• Added ability to download park pattern configs from configured bar
• Added safeguard to not rely on web services if services down
• To trigger upate you can restart the app and wait 2 minutes for download

05/08/24 - v0.1.39 Beta:

• Allow Quad to bypass 60 day lockout
• Changed WORK to Work Light, change STT to Stop Tail Turn
• Removed single level TAKE DOWN from all products except Mini Lightbar and full lightbars

02/19/24 - v0.1.35 Beta:

• 1. Allowing manual entered PUIDs with disconnected bar to be registered on first entry
• 2. Added feature lockout of configs and unlock levels for disabled PUIDs

01/09/24 - v0.1.34 Beta:

• 1. After locked out period allow for pattern programming on unused inputs
• 2. Allow colors to be copied over to other modules when configuring single, dual or tri
• 3. Fixed WK and STT not deselecting from flashing download configs
• 4. Worked out download Mini27 download config layout issue
• 5. Allow for low power to be set on input with other set modes
• 5. Added ability to remve credit cards from Account page

01/04/24 - v0.1.32 Beta:

• 1. Fixed 60 day lockout issue with 2024 year change

08/30/23 - v0.1.30 Beta:

• 1. Fixed lightstick, mini light bar, and interior light bar configuration file loading. Some modules would show as set to a mode, but when programmed and activated 3 of the modules wouldn't turn on. This was only directly after loading the config file. The modules would work after manually configuring them after that.
• 2. Added Split Arrow as a product type option to the software. When plugging in the new Split Arrow product it will now show in the software.
• 3. Made setting STT, TD, and Work light easier for single color products. Added option to skip a module when setting these up if the module is already set up to be STT, TD or Work.

05/08/23 - v0.1.29 Beta:

• 1. Updated flash patterns for dual, tri, and quad to change color faster multiple times during the flash pattern and not wait until the end of the pattern.
• 2. Updated all Quantum products to allow for downloading the current configuration from the product into the software for editing.
• 3. Lock out color change ability after 60 days for single, dual, and tri. Quad is unaffected by this. This update will allow pattern changing and mode changing for the life of the product.
  The color change that is being locked out after 60 days is from first program of the product and limits the user from changing the colors of the module in the 1st configuration screen.
  Nothing in the second screen where the inputs are configured will be locked out.
• 4. Mini 18" and 27" modules were incorrectly mapped in the software. This was fixed allowing full functionality of this product.
• 5. Ability to make any input a pattern change input. Pattern change will only work on flash mode or left and right directional. It will not work on center directional.
• 6. Added work light for single color products. This is a rear facing white light.
• 7. Fixed an issue with a PWM signal being applied to an input pausing a flash pattern.
• 8. Checking for update was shorted to activate 30 seconds after program boot up and not several minutes.
• 9. Added the ability to create center out slow by activating left directional and right directional pattern.

  NOTE: For this to work every module that is set as left direction MUST be set as right directional on your second input that is being activated.
  If any of the modules are left out the modules will light out of sync when activating both left and right directional.

• 10. A default single color configuration was added to all products except for 44", 49", and 60" light bars. Here is the configuration:
    Input 1 - Dim 10%
    Input 2 - Pattern Change
    Input 3 - Mode 1
    Input 4 - Mode 2
    Input 5 - Takedown
    Input 6 - Left Arrow
    Input 7 - Right Arrow
    Input 8 - Take Down Flashing 2 center modules
    Input 9 - Left Brake
    Input 10 - Right Brake
•   
•   - To activate brakes. Apply 12V+ to Input 9 and/or Input 10 then tap pattern change. This will enable or disable brakes. When brakes are enabled they will not flash with the flash patterns.
•   - To activate Take down. Apply 12V+ to Input 5 and tap pattern change. This will enable or disable takedown.
    (When takedown is enabled the two takedown modules will not flash with Mode 1 or Mode 2)
    (You must use Input 1 takedown flashing to flash these modules)
•   
• What do I need to do to get these updates?
    - These changes will all be available as new features or bug fixes only with the newest release of the products firmware and software.
    The new software v0.1.29 is full backwards compatible with all existing Quantum hardware.
•   
• You will need the following to use these new features:
    1. Download and install 0.1.29 Unlock Software
    2. A 44", 49", and 60" light bar the PUID will end with -000044. Anything before this will not have these changes available.
    So for instance -000043 will not have these changes available.
    3. All other products the PUID will end with -100055. Anything before this will not have these changes available.
    So for instance -100054 will not have these changes available.

03/27/23 - v0.1.28 Beta:

• 1. Grayed out quad tab on quantum input selection with red info text under each tab
• 2. This will help communicate to users that only quantum or quad can be configured not both
• 3. The user needs to update the software via an update over wifi. This can be done by restarting the software and waiting 2 minutes

02/27/23 - v0.1.27 Beta:

• 1. Fixed mini lightbar module config order and naming for mini lightbar inputs
• 2. This will make it easier to configure mini lightbars and add custom input text
• 3. The user needs to update the software via an update over wifi. This can be done by restarting the software and waiting 2 minutes

02/10/23 - v0.1.26 Beta:

• 1. Added 44" Lightbar configuration

01/27/23 - v0.1.25 Beta:

• 1. Handling javscript USB disconnect error message

01/24/23 - v0.1.24 Beta:

• 1. Initial Release